Joystick Extension for Winwing 40 x 0

This joystick extension fits the Winwing Joystick ranges listed below.

Important: Please watch the video below before purchase for the correct way to install a QR4rigs Extension in to a Winwing Base. 

Video: https://youtu.be/BefC71nKLtA

NOTE: You must confirm you have watched the installation video before you are able to purchase this item.

The main tube is 30mm in diameter and has no offset but adds 40mm height.

Unlike most others available, this extension is fully hardwired allowing easy no-fuss swap out between joystick handles and extension/no extension modes.

The plug and the socket on the extension can be rotated to suit the orientation of the sockets and plugs on the Winwing original bases and grips. This is necessary as the rotation of the socket in some Winwing Bases differ from others, even the same models. DO NOT OVER ROTATE the plug and socket in the extension when aligning, just rotate enough to line them up properly. Spinning them round for laughs will break the wiring eventually causing failure.

There is a grub Screw on the top knurled screw and 2 stainless steel catch plates on the bottom screw section for the grub screw on the base.

Compatibility

NOTE: Our extensions over 50mm height are not compatible if the MFSSB Kit is installed.

• Winwing Joystick Bases and Winwing Joystick Grips
• No other bases or grips are considered compatible at this time.

Winwing Bases

• Orion 2 Joystick Base

NOTE: Winwing do not advise using extensions with their Orion 1 base.

Winwing Grips

• F-16EX Viper Metal Joystick Grip
• F/A-18 Hornet Metal Joystick Grip
• Orion2 Airbus A3XX Joystick Grip

Note: Adding an extension with an offset to a Winwing base will most likely require the use of heavier springs and for the larger extensions >175mm may require 2 springs on the forward backward axis to keep the stick centered.
Pushing your joystick beyond it's movement limits with force may result in breaking the extension itself, particularly with the longer extensions.

Instructions:
Notes

• Please watch video above before attempting an installation.
• To install the extension you will need to remove the grip from the base in the usual manner, before carrying out the installation.
• The Joystick extension must be installed on the base (A) before adding the grip (B).
• Do not overtighten either of the grub screws
• Rotate only the knurled screw nuts.
• DO NOT ROTATE THE GRIP!
• DO NOT OVER ROTATE the plug and socket in the extension when aligning with base and grip.
• Take care to align the plugs and sockets to avoid damaging them.
• NEW! From 28th October 2023, 2 rubber washers are supplied with the kit making a much tighter connection between the mating surfaces, so much so, that using and tightening the grub screws is now optional.

A. Extension Installation to Base

1. If installed, loosen the grub screw so that it is clear of the internal threads on the Knurled Base Screw on the base.
2. Place one of the rubber washers on top of the mating surface on the base around the socket.
3. Carefully align the plug on the base of the extension with the socket in the Winwing base. When aligned it should go in easily and the mating surfaces should be flat.
4. Turn the extension to the desired orientation and hold in place. DO NOT over rotate the extension.
5. Tighten the knurled base screw by hand, whilst holding the extension pole still. Do not use tools on the knurled base screw but make sure it is tight. The grub screw (or grub screw hole should align with the metal catch plate at either the front or the back of the extension.
6. (optional) Install and tighten the grub screw. Do not overtighten the grub screw, to the pinch is adequate.

B. Grip Installation to Extension

1. If installed, loosen the grub screw so that it is clear of the internal threads on the Knurled Screw on the extension.
2. Place one of the rubber washers on top of the mating surface on the top of the extension around the socket.
3. Pull the ps2 cord from the grip a little and carefully align the plug with the socket of the extension.
4. Push the plug in to the socket. The socket will rotate to match the orientation of the ps2 cord plug as you put them together.
5. Change the orientation of the grip to your desired angle. When aligned the mating surfaces should be flat.
6. Turn the extension to the desired orientation and hold in place. DO NOT rotate the extension or the grip further, only turn the knurled screw.
7. Tighten the knurled screw by hand, whilst holding the extension pole and grip still. Do not use tools on the knurled screw but make sure it is really tight. The grub screw (or grub screw hole should align with the flat surface at either the front or the back of the grip screw.
8. (optional) Install and tighten the grub screw. Do not overtighten the grub screw or you may damage the threads, to the pinch is adequate.

If you need a different height or offset, please use Custom Joystick Extension Request form to get in touch!

Note: This item is 3D printed. There will be obvious print lines on this product due to the nature of 3D printing. The colour of the base interface, plug and socket holder (not visible once installed) will vary depending on model chosen. We have colour coded them to make sure we send you the right one!