Winwing Base to Thrustmaster Grip Conversion Extension

This plug and play extension enables a Thrustmaster Joystick Grip to be used on a Winwing Joystick Base (where firmware allows).

New: We have updated the product with Anodised Alumium Threaded ends and a different printing process for the main tube inline with our new Genβ (Generation Beta) release of extensions.

The main tube is 30mm in diameter, is finished in silver/grey and comes in a choice of 3 different heights, 50mm, 75mm and 100mm. 

Unlike most others available, this extension is fully hardwired allowing easy no-fuss swap out.

The plug on the extension can be rotated to suit the orientation of the socket on the Winwing original bases. This is necessary as the rotation of the socket in some Winwing Bases differ from others, even the same models. DO NOT OVER ROTATE the plug in the extension when aligning, just rotate enough to line it up properly. Spinning it around for laughs will break the wiring eventually causing failure.

A 0.5mm rubber washer is supplied to be placed at the bottom of the converter (Winwing side) to aid in the prevention of rotation when tightened.

This Conversion Extension can be used in conjunction with our other Genβ extensions designed for Winwing or Thrustmaster by placing it either on top of a QR4rigs Genβ Winwing extension or at the base of a QR4rigs Genβ Thrustmaster Extension.

*Compatible with ALL QR4rigs extensions when used with a Winwing Joystick Base and Thrustmaster Grip.

**NOTE about Virpil Grips: Winwing firmware identifies Virpil (VPC) grips as TM Grips in general, therefore will only be as functional as putting the Virpil Grip on a TM base e.g. some of the extra axis and buttons will not be functional. This is a limitation of the firmware in the WW base and is not changed by the Conversion Extension.

NOTE. Winwing firmware needs to be up to date and the Conversion Extension will only work as well as the firmware allows.

Pushing your joystick beyond it's movement limits with force may result in breaking the extension itself, particularly with the longer extensions.

Compatibility

NOTE: Our conversion extensions are now compatible if the MFSSB Kit is installed.

• Winwing Joystick Bases and Thrustmaster Joystick Grips
• QR4rigs Thrustmaster extensions*
• QR4rigs Winwing extensions*
• Partial support for Virpil Grips**
• No other devices are considered compatible at this time.

Winwing Bases

• Orion 2 Joystick Base

Thrustmaster Grips

• Thrustmaster Warthog Grip
• Thrustmaster F/A-18C Grip
• Thrustmaster Cougar Grip

Partial support for Virpil Grips** (see Notes above)

• VPC WarBRD Grip
• VPC V.F.X Grip
• VPC MongoosT-50 Series Grips
• VPC Constellation ALPHA Series Grips
• VPC Constelation DELTA

Naming Convention

Instructions:
Notes

• The Conversion Extension must be installed on the base or extension (A) before adding the grip (B).
• Do not overtighten the grub screw on the WW Base or WW Extension
• Rotate only the knurled screw nuts on the WW Base or TM Grip.
• DO NOT ROTATE THE CONVERSION EXTENSION!
• DO NOT OVER ROTATE the plug in the extension when aligning with base.
• Take care to align the plugs and sockets to avoid damaging them.
• A rubber washer is supplied with the kit making a much tighter connection between the mating surface of the WW Base and the conversion extension.
• Using the grub screw on the WW base is not supported or needed.

A. Conversion Extension Installation to Winwing Base

1. If installed, remove the grub screw from the Knurled Base Screw on the base.
2. Place the rubber washer on top of the mating surface on the base around the socket.
3. Carefully align the plug on the base of the conversion extension with the socket in the Winwing base. When aligned it should go in easily and the mating surfaces should be flat.
4. Rotate the conversion extension to the desired orientation and hold in place. DO NOT over rotate the conversion extension. The QR4rigs writing on the tube should face AWAY from the pilot.
5. Tighten the knurled base screw by hand, whilst holding the conversion extension still and ensure sure it is tight. DO NOT use the grub screw.

B. Thrustmanster Grip Installation to Conversion Extension

1. Carefully align the plug on the bottom of the grip with the socket of the extension.
2. When aligned the mating surfaces should be flat.
3. DO NOT rotate the conversion extension or the grip, only turn the knurled screw.
4. Tighten the knurled screw by hand, whilst holding the extension pole and grip still. Ensure the knurled screw is really tight.

If you need a different height, please use Custom Joystick Extension Request form to get in touch!

Note: Parts of this item are 3D printed. There will be obvious print lines on this product due to the nature of 3D printing.